Directional Valves — HyPerformance™

HPC10-J49— Piloted Directional Element, Balanced Poppet, Normally Open
  Selection guide - similar valves.
  PDF file of this page.
  Request a quote.

HPC10-J49 Valve

SYMBOL:HPC10-J49 Valve symbol
A high pressure, two-way, bi-directional, pilot-to-open, balanced poppet-type, screw-in,
cartridge-style, hydraulic directional element designed to function as a load-holding or
blocking valve in applications requiring low internal leakage.

In the unpiloted state, the HPC10-J49 allows flow from 1 to 2 bi-directionally. On remote
pilot signal at port 4, the valve shifts to block flow from ports 1 to 2 bi-directionally.
The spring chamber is vented to port 3. Pressure at port 3 will directly affect the pilot
pressure required to shift the valve and must be added. The hydraulically balanced poppet
will allow ports 1 and 2 to be fully pressurized without affecting required pilot pressure to
actuate the valve. With port 3 vented, the valve will fully shift with a minimum pilot pressure
of 17 bar (250 psi).

• Bi-directional flow.
• Balanced poppet.
• Low internal leakage.
• All HyPerformance products are tested to the rigorous standards of the NFPA
   specification T2.6.1.
• All HyPerformance valves are tested at a verification level of 90% and an
   assurance of 99%.

Operating Pressure: Ports 1 & 2 (work ports): 350 bar (5075 psi); 10% cycle life:
   420 bar (6090 psi); Port 4 (pilot): 207 bar (3000 psi); Port 3 (tank): 69 bar (1000 psi)
   Note: All HyPerformance products are tested for 900K cycles at 350 bar and 100K
   at 420 bar.
Proof Pressure: 690 bar (10000 psi)
Burst Pressure: 1380 bar (20000 psi)
Flow: 76 lpm (20 gpm)
Internal Leakage: 10 drops/min between ports 1 and 2 at 35 bar (500 psi) and 350 bar (5075 psi)
Temperature: -40 to 100° C (-40 to 212° F) with standard Buna seals;
   -26 to 204° C (-15 to 400° F) with fluorocarbon seals;
   -54 to 107° C (-65 to 225° F) with urethane seals
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
   7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Cavity: HVC10-J4; See page 9.110.1_4w
Cavity Tool: HCT10-J4XX; See page page 8.600.1
Seal Kit: SK10-J4N-BBM (Buna N); SK10-J4V-BBM (fluorocarbon);
   SK10-J4U-000 (urethane); See page 8.650.1


HPC10-J49 Performance graph 1



HPC10-J49 Valve Dimensions



Cartridge: Weight: 0.3 kg (0.65 lb) Steel with hardened work surfaces. Zinc-nickel plated exposed surfaces. PPDI urethane seals without back-up rings standard. Buna N and fluorocarbon seals also available.

Standard Ported Body: Weight: 2.3 kg
(5.2 lb) H-series ductile iron standard. Rated to 345 bar (5000 psi). See page 8.010.1_4w.



HPC10-J49 Ordering Chart Manual Override Options