Electro-Proportional Valves — Flow Control HyPerformance™HSPEC10-34 — Proportional Flow Control Vavewith Integral Compensator |
Features and Benefits Selection guide - similar valves. PDF file of this page. Request a quote. |
---|

SYMBOL:

DESCRIPTION
A high pressure, proportional, solenoid-operated, poppet-type, restrictive type, pressure
compensated, normally closed, flow control, screw-in hydraulic cartridge valve with built-in
damping and load-holding features.
OPERATION
With inlet at port 3, the HSPEC10-34 will regulate flow out of port 2 regardless of load pressure
with flow rate proportional to current applied to the solenoid. Port 1 must be connected to port 3
to provide load-sense function for the compensator. When de-energized, the valve blocks flow from
port 3 to port 2, allowing free flow in opposite direction.
FEATURES
• Sealed integral compensator.
• Continuous-duty rated coils.
• Optional manual override.
• Optional waterproof E-Coils rated up to IP69K.
• All HyPerformance™ valves are tested to the rigorous standards of NFPA specification T2.6.1 and
are tested at a verfication level of 90% and an assurance of 99%.
RATINGS
Operating Pressure: 350 bar (5075 psi); 10% cycle life; 420 bar (6090 psi)
Note: All HyPerformance™ products are tested for 900K cycles at 350 bar and 100K at 420 bar.
Proof Pressure: 690 bar (10000 psi)
Burst Pressure: 1380 bar (20000 psi)
Flow: 30 lpm (8 gpm)
Maximum Internal Leakage: (at 350 bar/5075 psi): Port 3 to port 2: 7 drops/minute;
Port 1 to 3 (sealed piston): zero leakage
Temperature: -54° to 107°C (-65° to 225° F) with urethane seals
Electrical Parameters (with size 10 E-Series coil):
A high pressure, proportional, solenoid-operated, poppet-type, restrictive type, pressure
compensated, normally closed, flow control, screw-in hydraulic cartridge valve with built-in
damping and load-holding features.
OPERATION
With inlet at port 3, the HSPEC10-34 will regulate flow out of port 2 regardless of load pressure
with flow rate proportional to current applied to the solenoid. Port 1 must be connected to port 3
to provide load-sense function for the compensator. When de-energized, the valve blocks flow from
port 3 to port 2, allowing free flow in opposite direction.
FEATURES
• Sealed integral compensator.
• Continuous-duty rated coils.
• Optional manual override.
• Optional waterproof E-Coils rated up to IP69K.
• All HyPerformance™ valves are tested to the rigorous standards of NFPA specification T2.6.1 and
are tested at a verfication level of 90% and an assurance of 99%.
RATINGS
Operating Pressure: 350 bar (5075 psi); 10% cycle life; 420 bar (6090 psi)
Note: All HyPerformance™ products are tested for 900K cycles at 350 bar and 100K at 420 bar.
Proof Pressure: 690 bar (10000 psi)
Burst Pressure: 1380 bar (20000 psi)
Flow: 30 lpm (8 gpm)
Maximum Internal Leakage: (at 350 bar/5075 psi): Port 3 to port 2: 7 drops/minute;
Port 1 to 3 (sealed piston): zero leakage
Temperature: -54° to 107°C (-65° to 225° F) with urethane seals
Electrical Parameters (with size 10 E-Series coil):
Hysteresis: 5.7 lpm (1.5 gpm) maximum
Dither/PMW Frequency Range: 100 to 200 Hz
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Cavity: HVC10-3; See page 9.110.1_3w
Seal Kit: SK10-3U-0; See page 8.650.1
Dither/PMW Frequency Range: 100 to 200 Hz
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Cavity: HVC10-3; See page 9.110.1_3w
Seal Kit: SK10-3U-0; See page 8.650.1
PERFORMANCE:


DIMENSIONS:
MATERIALS:
Cartridge: Weight without coil and nut: 0.19 kg
(0.43 lb); Weight with manual override: 0.20 kg (0.45 lb) Steel with hardened work surfaces.
Zinc-plated exposed surfaces. PPDI urethane seals without back-up rings standard.
E-Coil: Weight: 0.41 kg (0.9 lb); Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors.
See page 3.400.1_10-size.
Ported Body: Weight: 1.40 kg (3.09 lb); H-series ductile iron standard. Rated to 345 bar (5000 psi). Aluminum body also available, dimensions may differ. See page 8.010.1_3w.
Cartridge: Weight without coil and nut: 0.19 kg
(0.43 lb); Weight with manual override: 0.20 kg (0.45 lb) Steel with hardened work surfaces.
Zinc-plated exposed surfaces. PPDI urethane seals without back-up rings standard.
E-Coil: Weight: 0.41 kg (0.9 lb); Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors.
See page 3.400.1_10-size.
Ported Body: Weight: 1.40 kg (3.09 lb); H-series ductile iron standard. Rated to 345 bar (5000 psi). Aluminum body also available, dimensions may differ. See page 8.010.1_3w.
ORDERING CHART:
