Solenoid-Operated On/Off Valve — HyPerformance™

HSV10-25 — Spool-Type, 2-Way, Normally Open
  Selection guide - similar valves.
  PDF file of this page.
  Request a quote.

HSV10-25 Valve

SYMBOL:HSV10-25 Valve symbol

A solenoid-operated, 2-way, normally open, spool-type, screw-in hydraulic cartridge valve designed for
bi-directional blocking in high pressure applications.

When de-energized, the HSV10-25 allows flow in both directions. When energized, the valve closes to
block bi-directional flow. When energized, the cartridges spool shifts to close the bidirectional flow
Operation of Manual Override Option: The manual override feature is intended for emergency use,
not continuous duty operation. To override, push button in and twist counterclockwise 180°. The
internal spring will push the button out. In this position, the valve may be only partially shifted. To
assure full override shift, pull the button out to its fullest extension and hold it in this position. To return
to normal valve function, push button in, twist clockwise 180° and release. Override will be detented in
this position.

• Continuous-duty rated coil.
• Hardened seat for long life and low leakage.
• Optional coil voltages and terminations.
• Both ports may be fully pressurized.
• Efficient wet-armature construction.
• Cartridges are voltage interchangeable.
• Waterproof E-Coils rated up to IP69K.
• Unitized, molded coil design.
• 1000-hour salt-spray rated solenoid tubes and coils.
• All HyPerformance products are tested to NFPA specification T2.6.1
  and are tested at a verification level of 90% and an assurance of 99%.

Operating Pressure: 350 bar (5075 psi); 10% cycle life: 420 bar (6090 psi)
  Note: all HyPerformance products are tested for 900K cycles at 350 bar and 100K cycles at 420 bar.
Burst Pressure: 1380 bar (20,000 psi)
Flow: Up to 30.3 lpm (8 gpm)
Internal Leakage: Port 2 to 1: 131 ml/minute (8 cu. in/minute) max. at 350 bar (5075 psi);
  Port 1 to 2: 279 ml/minute (17 cu. in/minute) max. at 350 bar (5075 psi)
Temperature: -54° to 107°C (-65° to 225°F) with Urethane seals
Coil Duty Rating: Continuous from 85% to 115% of nominal voltage
Initial Coil Current Draw at 20°C: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
  7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Cavity: HVC10-2; See page 9.110.1_2w
Cavity Tool: HCT10-2xx See page 8.600.1
Seal Kit: SK10-2U-O; See page 8.650.1
Coil Nut: Part No. 4555250


HSV10-25 Valve Performance Chart

HSV10-25 Valve Dimensions


Cartridge: Weight: 1.19 kg.
(2.62 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces; Urethane
O-ring without back-up standard.

Ported Body: Weight: 0.19 kg. (0.41lbs.); HyPerformance Ductile iron (code 'D') standard. Rated to 345 bar (5000 psi).
See page 8.010.1_2w.

E-Coil: Weight: 0.41 kg.
(0.9 lbs.); Perfect wound, fully encapsulated with rugged external metal shell; Rated up to IP69K with integral connectors.
See page 3.400.1_10-size.

HSV10-25 Ordering Chart 10-size E-Coil

Selection guide - similar valves.
PDF file of this page.   Request a quote.