Cartridge Valves - Solenoid Valves - 2-Position 2-Way - Poppet Type - Normally Closed - Free Reverse Flow

HSV10-P22A

SOLENOID CARTRIDGE VALVE POPPET, 2 PORT, NORMALLY CLOSED WITH INTEGRAL POSITION SENSOR

Overview

Description

The HSV10-P22AX is a high pressure 2-way, piloted, poppet-type, normally closed, screw-in hydraulic cartridge valve designed to function as a load holding or blocking valve in applications requiring low internal leakage.

Operation

When de-energized, the HSV10-P22AX blocks flow from port 2 to 1. in this mode the cartridge will allow flow from port 1 to 2 after overcoming the spring forces (see performance graph). When energized, the valve will allow flow bi-directionally.

Manual Override Operation

For normal operation (de-energized) the manual override pin must be seated in the lower detent groove. to shift the valve manually, the operator pushes down on the knob and rotates 180 degrees in either direction. When the manual override is actuated, increased flow can be achieved by pulling on the knob.

NOTE: The manual override feature is intended for emergency use, not for continuous-duty operation.

Features

  • Integral position sensor indicates when valve is shifted.
  • Continuous-duty rated coil.
  • Hardened seat for long life and low leakage.
  • Optional coil voltages and terminations.
  • Efficient wet-armature construction.
  • Cartridges are voltage interchangeable.
  • Waterproof E-Coils rated up to IP69K.
  • Unitized, molded coil design.
  • 960 hour salt-spray rated solenoid tubes and coils.
  • All HyPerformance products are tested to NFPA specification T2.6.1 and are tested at a verification level of 90% and an assurance of 99%.
Pressure Ratings
Pressure rating:
  • 350 bar (5075 psi)
Proof pressure:
  • 690 bar (10000 psi)
Burst pressure:
  • 1380 bar (20000 psi)
Flow Ratings
Flow rating:
  • 75.5 lpm (20 gpm)
Maximum internal leakage:
  • 5 drops/min With 350 bar (5075 psi)
  • 10.2 lpm (2.7 gpm) Typical flow (leakage) in transition at 345 bar (5000 psi). (see "Flow vs % Valve Shift" graph for flow in transition from valve close to valve open).
Other Ratings
Cycle life:
  • One million cycles
Response:
  • 0.050 sec Pull-in. Response times measured per NFPA/T3.5.30-2008 *Inlet pressure 345 bar (5000 psi) *Valve oriented vertically (2-1) and purged of air
  • 0.065 sec Drop-out. Response times measured per NFPA/T3.5.30-2008 *Inlet pressure 345 bar (5000 psi) *Valve oriented vertically (2-1) and purged of air
Temperature Ratings
Operating fluid temperature:
  • -40 to 100 °C (-40 to 212 °F) With buna N seals
  • -26 to 204 °C (-15 to 400 °F) With fluorocarbon seals *See Position sensor operating temperature*
  • -54 to 107 °C (-65 to 225 °F) With urethane seals *See Position sensor operating temperature*
Storage temperature:
  • -40 to 70 °C (-40 to 160 °F)
Ambient temperature:
  • -40 to 70 °C (-40 to 160 °F)
Position sensor operating temperature:
  • -40 to 110 °C (-40 to 230 °F) Sensor element operating temperature limits the operating temperature of the entire assembly
Fluids:
  • Mineral based or synthetic hydraulic fluid with lubricating properties
Fluid viscosity range:
  • 7.4 to 420 cSt
Maximum operating contamination level:
  • 18/16/13 per ISO 4406
Electrical Parameters
Supply voltage:
  • 9 to 32 Vdc Vcc
Output voltage with target present:
  • Vcc
Output clamp current:
  • 40 to 65 mA For Vcc up to 32 Vdc
Ratings
ESD:
  • ±8 kV Air discharge
EMI:
  • 30 V/m From 400 MHz to 2 GHz
IP rating:
  • IP67
Vibration:
  • 10 G 10 to 2000 Hz sinosudial
Mechanical shock:
  • 50 G 11 ms, half-wave sinosudial
Properties
Connector:
  • Deutsch DT04-4P Option N3 (dual output)
  • M12 Option M3 (dual output)
Unit weight:
  • 0.51 kg (1.12 lb) Cartridge
Internal wetted surface area:
  • 308 cm² (47.8 in²)
HSV10-P22A_Perf1(2022-02-24) HSV10-P22A_Perf2(2022-02-24)
HSV10-P22A_Dim1(2022-02-24) HSV10-P22A_Dim2(2022-02-24)
HSV10-P20A_Sym2(2022-02-24) HSV10-P20A_Sym3(2022-02-24)
Cavity:
Cartridge installation torque:
  • 102 to 115 N-m (75 to 85 ft-lb) Steel/ductile iron cavity
Orientation restriction:
  • None
Seal kit:
  • SK10-2N-M Buna N
  • SK10-2V-M Fluorocarbon
  • SK10-2U-O Urethane
HSV10-P22A_Order(2022-02-24)

Model Options

HSV10-P22AE-H-J-L-M
E Manual Override
CODE
DESCRIPTION
BLANK
NONE
M
Two Position Override, Red Knurled Knob
H Line Body
CODE
DESCRIPTION
0
No Body
J Seal
CODE
DESCRIPTION
N
Buna-N
V
Fluorocarbon
U
PPDI Urethane
L Coil
CODE
DESCRIPTION
0
No Coil
10EL
10 VDC, E-Coil, Dual Lead Wires
10ER
10 VDC, E-Coil, Deutsch
10ER/Z
10 VDC, E-Coil, Deutsch with Zener Diode
12EG
12 VDC, E-Coil, DIN 43650
12EJ
12 VDC, E-Coil, AMP Jr.
12EL
12 VDC, E-Coil, Dual Lead Wires, 18 inches long
12EL/36
12 VDC, E-Coil, Dual Lead Wires, 36 inches long
12EL/W/Z
12 VDC, E-Coil, Dual Lead Wires with WeatherPak and Zener Diode
12EL/Z
12 VDC, E-Coil, Dual Lead Wires with Zener Diode
12ER
12 VDC, E-Coil, Deutsch
12ER/Z
12 VDC, E-Coil, Deutsch with Zener Diode
12EY
12 VDC, E-Coil, Metri-Pack 150
12EY/Z
12 VDC, E-Coil, Metri-Pack 150 with Zener Diode
20ER
20 VDC, E-Coil, Deutsch
24EG
24 VDC, E-Coil, DIN 43650
24EJ
24 VDC, E-Coil, AMP Jr.
24EL
24 VDC, E-Coil, Dual Lead Wires, 18 inches long
24EL/36
24 VDC, E-Coil, Dual Lead Wires, 36 inches long
24EL/W/Z
24 VDC, E-Coil, Dual Lead Wires with WeatherPak and Zener Diode
24ER
24 VDC, E-Coil, Deutsch
24ER/Z
24 VDC, E-Coil, Deutsch with Zener Diode
24EY
24 VDC, E-Coil, Metri-Pack 150
24EY/Z
24 VDC, E-Coil, Metri-Pack 150 with Zener Diode
M Position Sensor Termination
CODE
DESCRIPTION
BLANK
No Position Sensor
M3
Neutral Sense, M12-4P, Dual Output NC/NO
N3
Neutral Sense, DT04-4P, Dual Output NC/NO